![do the saber and astro saber use the same programming cable do the saber and astro saber use the same programming cable](https://intelgenius.weebly.com/uploads/1/2/4/0/124017831/707062108.jpg)
- #Do the saber and astro saber use the same programming cable software#
- #Do the saber and astro saber use the same programming cable free#
The 7th character spot and the "L" must be in the 8th spot. Notice the "URCALL"Ĭolumn "REF077CL" means "Link to Reflector 077 C module". Or "Minus Shift" with a 0MHz offset as shown above (I know, it's weird).ĥ0 above, "Nano-TN" is the Tennessee-wide Reflector 077C. Must select the "DR" Digital Repeater mode. Out as "K9OJ/ROB" which is a common D-STAR technique. You need to start withĪccess so you can use net-linked D-STAR repeaters. Get wrong will keep you from communicating with the hotspot. Hotspot D-STAR was difficult with lots of little details that if you Very similar to P25 because they both use C4FM and sound like soft static.įrequency Shift Keying & Frequency Modulation) digital modulation like P25 but YSF uses 12.5kHz of bandwidth like DMR & P25.
![do the saber and astro saber use the same programming cable do the saber and astro saber use the same programming cable](https://www.cryptomuseum.com/crypto/motorola/saber/img/302741/004/full.jpg)
Prevent your radio from decoding your hotspot's transmissions. Reception bit error rate (Local RF Activity BER). If only otherĬallsigns show high loss then they have a connection problem. Hotspot's connection to the internet has a problem. If your radio transmissions to the hotspot show a high loss then the Pi-Star's Admin/Live Logs display will give you more detail on what the hotspotĮxcessive "Loss" (shown on Pi-Star dashboard) means data loss on data Into repeater mode and transmit on the wrong frequency. Your hotspot frequency in a repeater band your radio may automatically switch Make sure your radio is in simplex mode when using a hotspot. Verify the radio transmit mode is showing "DN" (digital narrow) on the display.Ĭheck the radio and hotspot frequencies are the same. Use an analog radio to monitor the hotspot and radio's transmissions. Transmit and you should see activity in the "Local RF Activity" section. Yaesu FT1DR Hotspot ProgrammingĪ simplex frequency is all that's needed. You can now change YSF "rooms" using DTMF tones. YSF-to-NXDN and YSF-to-P25 so you can access these modes with one Yaesu C4FM Into the "A" VFO and hit the "Dx" button until "DN" (digital narrow) isĭisplayed and you're all set. Just program your hotspot frequency as simplex Yaesu System Fusion C4FM is super simple.
#Do the saber and astro saber use the same programming cable software#
TH-D74 DMR Tytera MD-380 P25 Motorola XTS3000ĭUDE-Star & DROID-Star Software Based Ham This can help you quickly dial in the correct Have an SDR with computer output, use it to monitor your radio and hotspot toĬompare their exact frequency. Hotspot is transmitting and your radio is transmitting in digital mode. Your radio and hotspot transmissions on an SDR or analog radio so you can verify the Here's a rundown on what I had to do to get each radio setup: With a hotspot was much more difficult than setting up the hotspot and Pi-Star I paired it withĪn old $35 raspberry pi 2 with Pi-Star. Generic Chinese MMDVM_HS_HAT_Duplex Pi Hatĭual radios allow simultaneous reception and transmission.
![do the saber and astro saber use the same programming cable do the saber and astro saber use the same programming cable](https://www.debcoelectronics.com/wp-content/uploads/2017/02/3047-918-4-300x300.jpg)
The Jumbo Spot transmitter is rated at 20 milliwatts. Radio, OLED screen and support Pi-Star, YSF, D-STAR, DMR, P25, NXDN and The Nano-Spot and Jumbo Spot RTQ both have Wi-Fi, 70cm
#Do the saber and astro saber use the same programming cable free#
To communicate with my hotspots so I created this webpage to hopefully help new hotspot users get up-and-running easierĭigital Ham radio before buying an expensive radio you can useĪnd DROID-Star (droid phone based) free software to monitor and transmit on P25,ĭMR, D-STAR, YSF and others including the exciting new M17 protocol. I had a heck of a time getting my digital radios Radios with dual antennas for simultaneous UHF transmit and receive. HAT works great and it's what I currently recommend everyone get. I paired it with a $35 pi 2 and open top pi case. The Jumbo Spot uses a Pi Zero W with standard Linux Its MMDVM firmware can be upgraded by following
![do the saber and astro saber use the same programming cable do the saber and astro saber use the same programming cable](https://s3.manualzz.com/store/data/023293758_1-7f20da903394cf8f08f3ebab7d468ba5.png)
Uses a Raspberry Pi clone (it seems to be a NanoPi) with a non-standard Nano-Spot comes in a nice case and has an external Wi-Fi antenna but it's functionally almost identical and took about a month for delivery due to high demand. I used to own a Nano-Spot which was $269 (now $299) from Running Pi-Star as the Nano-Spot with its more powerful quad core processor. Although it runs on a Pi Zero W it performs just as well Jumbo Sport from (now $29)īut it took about three weeks for delivery. Powerful Pi-Star software for configuration and control. Jumbo Spot for D-STAR, P25, YSF and POCSAG and the MMDVM_HS_HAT_DUPLEX for DMR. Both can doĮverything Pi-Star can dish out including Yaesu System Fusion (YSF), DMR,ĭ-STAR, P25, NXDN, POCSAG paging, YSF-to-DMR, YSF-to-NXDN and YSF-to-P25. MMDVM_HS_HAT_DUPLEX pi hat + pi2 for all my digital ham radio needs. Amateur Radio Hotspot VHF & UHF Digital Modes